Manufacturers Details:
Smooth acoustic sound at louder volume levels.
* Volume control mounted at the soundhole
* A1.2N special design preamp (only for use with 1470 AST)
* Includes A1.2N preamp and 1470 AST transducer
* High-quality endpin output jack
* 750 hours average battery life
B-Band A1.2N Acoustic Guitar Endpin Preamp
This bundle includes a special version of the A1.2 that has a slight frequency notch of 6 decibels in the low-mids, giving the system a smooth acoustic sound at louder volume levels and is packaged along with, and for use only, with the 1470 AST. This gives you great tone at a great value. It can be used in any acoustic guitar, or similar instrument, that has good access to its interior.
This preamp bundle comes with a volume control that simply mounts at the inside edge of the sound hole with adhesive. The 9-volt battery powered electronics are mounted in a small tube that is directly coupled with a high quality endpin jack making an all-in-one structure. As an option, the A1.2N can be phantom powered with the B-Band external battery box.
The structure is light in mass adding very little weight to the instrument. Includes all mounting hardware, box-tight battery holder and wire harness.
Great amplified acoustic tone at a great value.
* S/N ratio: Greater than 90 dB
* Distortion: 0.05%
* Frequency response: 50 Hz to 40 kHz (+0, -3 dB)
* Input channel voltage gain: +24 dB
* Input impedance: 50 mOhms -|< 10 pF
* Output impedance: < 3.5 kOhms
* Nominal output level: -10 dBu (0.245 Vrms)
* Power supply: 9V battery (not included)
* Current consumption: 1.2 mA typical
* Connections: Transducer input, 2.54mm (3/32") header; Output, 6,3mm (1/4") jack
* Weight (with accessories): 50 g
* Size: 13x97mm
B-BAND A1.2 Endpin + UST
TRANSDUCER SET
Manufacturers Details:
Clean, clear acoustic guitar sound in amplified settings.
* Volume control mounted at the soundhole
* Add either 1/8 or 3/32 Undersaddle UST
* High quality endpin output jack
* 750 hours average battery life
B-Band A1.2 Acoustic Guitar Endpin Preamp
The A1.2 is the little brother of the classic B-Band A2 preamp and is big on classic B-Band sound. The single input A1.2 has a direct frequency response with 24 dB of gain, making a perfect fit with the B-Band UST (not included). The sound reproduction is amazingly pure and clear.
The A1.2 comes with a volume control that simply mounts at the inside edge of the sound hole with adhesive. The 9-volt-battery-powered electronics are mounted in a small tube that is directly coupled with a high quality endpin jack, making an all-in-one structure.
The structure is light in mass, adding very little weight to the instrument. Includes all mounting hardware, box-tight battery holder and wire harness.
* S/N ratio: Greater than 90 dB
* Distortion: 0.05%
* Frequency response: 50 Hz to 40 kHz (+0, -3 dB)
* Input channel voltage gain: +24 dB
* Input impedance: 50 mOhms -|< 10 pF
* Output impedance: < 3.5 kOhms
* Nominal output level: -10 dBu (0.245 Vrms)
* Power supply: 9V battery (not included)
* Current consumption: 1.2 mA typical
* Connections: Transducer input, 2.54mm (3/32") header; Output, 6,3mm (1/4") jack
* Weight (with accessories): 50 g
* Size: 13x97mm
B-BAND A2 ENDPIN PREAMP COMBOS
Manufacturers Details:
The A2 is ultimate in design for those who want to keep their instrument original with minimal intrusion.
The flexible dual input preamp offers several pickup and mic configurations and coupled with the sophisticated
HZZLess electronics reproduce all the instrument’s nuances.
The preamps input channel 1 will accept EITHER the UST or AST pickup. Input channel 2 can be configured to accept an AST,
or the B-Band AG-MIC soundhole condenser mic or a magnetic pickup. Separate output channels,
accessed with the use of a standard stereo cable, give the user control of the two sources at a mixer or preamp.
Inside the A2 is a matrix of four DIP-switches that determine specialties. At channel 1 there is a switch for enabling a
unique contour filter for upper register tone enhancement. For channel 2 there are DIP-switches to turn on bias
voltage for the AG-MIC, to turn on a high-pass filter for microphone feedback reduction and to lower the gain from
24 dB down to 0 dB.
A2 Systems
* AST and Condensor Mic
* UST and Condensor Mic
* AST and UST
B-BAND A2.2 XOM Endpin
Preamp + AST and UST
Manufacturers Details:
The A2.2 has a dual input / single output onboard preamp, for combining BOTH the UST and AST.
It includes the XOM technique with mix control to bring the best of the UST and AST characters together
resulting in a sound that is true to the guitars unique voice in any performance venue.
The A2.2 is also great for resonator guitars with spider or biscuit bridges. Using the
A2.2 system in a resonator guitar is simple. The UST pickup goes under the saddle and the AST is simply attached
to the resonator cone. In this way both pickups pickup the sound like no other system - At the Source!
The control pad of the A2.2 simply mounts at the sound hole of the guitar.
An optional 9-volt battery phantom power supply is available. The A2.2 has a small remote control pad with a volume
and mix control that mounts without modification at the inside edge of a guitar’s soundhole. The preamp is housed in
a lightweight all-metal box and can be mounted inside the guitar at the side or back and is powered with a 9-volt battery.
At the preamp there are two input gain trim controls for both the UST and AST to match input levels.
The entire system installs easily with very minor modifications – one small drill hole each for the
pickup and endpin jack. For fast connections all components plug in without soldering.
A2.2 System Features:
* AST and one UST pickup
* Dual channel input (UST and AST)
* XOM circuit
* HZZLess low noise / high output circuit
* Remote soundhole volume and mix controls
 |
B-BAND AST TRANSDUCER ONLY
Manufacturers Details:
* Use only with a B-Band Preamp
* Condenser acoustic soundboard transducer
* Operation based on a worldwide-patented elastic electret film
* Size 1470 fits to a wide variety of steel and nylon string acoustic guitars
* Reproduces original tone without affecting the instrument acoustically
* Ultra thin and light
* High gain before feedback
* Wide dynamic range
* Easy installation
* LINK TO B-BAND PRE AMPS |
 |
B-BAND UST TRANSDUCER ONLY
Manufacturers Details:
* Use only with a B-Band Preamp
* Condenser under saddle transducer
* Operation based on a worldwide-patented elastic electret film
* Sizes to fit a wide range of guitars
* Reproduces original tone without affecting the instrument acoustically
* Ultra thin, only 0.4 mm / .015"
* High gain before feedback
* Wide dynamic range
* Easy installation
* Narrow saddle slot instruments (2.2 mm / 3/32")
* Wide saddle slot instruments (2.9 mm / 1/8")
* LINK TO B-BAND PRE AMPS
|
 |
B-BAND A1.2 ENPIN ONLY
Manufacturers Details:
* Volume control mounted at the soundhole
* HZZLess low noise / high output circuit
* High quality endpin output jack
* Box-Tight battery holder
* 750 hours average battery life
* 9-volt phantom power option
* LINK TO B-BAND PRE AMPS
|
MORE ACOUSTIC GUITAR PICKUPS
CLICK ON BRAND FOR MORE
B-BAND A1.2 Endpin + AST TRANSDUCER SET
